Protects against dampness on exterior face of interior walls in cavity wall construction.

Protects against dampness on exteror surfaces of concrete, metal and wood above or below grade.

ASTM D-1187 Type II

ASTM D-1227 Type III

SS-R-1781

MIL-R-3472A

VOC Content: 20 g/L MAX

100 Non-Fibered Emulsion is a vapor retarder used as a protective coating against dampness on the exterior face of interior walls in cavity wall construction and exterior surfaces of concrete, metal and wood above or below grade. May also be applied to interior surfaces in the absense of hydrostatic pressure. 100 Non-Fibered Emulsion may be utilized as an adhesive for polystyrene insulation prior to backfilling.

‍

Weight per Gallon: 8.5 lbs
Solids by Weight: 52% Nominal
Solids by Volume: 49% Nominal
Color: Black
Permeance: 0.5 metric perms
Application Temp.: 40°F to 120°F
Dry Time: 2 to 4 hours @ 77°F and 50% Relative Humidity
Cure Time: 24 to 48 hours @ 77°F and 50% Relative Humidity
Service Temp (Cured Film): -5°F to 180°F

SURFACE PREPARATION:
All surfaces should be clean and free from oil, grease, dust, dirt and other foreign matter. Recommended application temperature is 40°F to 120°F. Dry surfaces may be dampened with water before application.

APPLICATION:
100 Non-Fibered Emulsion is easily applied by brush, roller or airless spray equipment.  Work coating into all cracks and crevices. Apply in one coat. If applying in two coats, allow the first coat to dry. Coating should be continuous and free of pinholes and holidays. Cover all slots, joints and grooves and apply into all chaes and corners.

Above-grade dampproofing (interior and exterior cavity walls) and Below-grade dampproofing (interior, exterior and cavity walls): Apply one coat of 100 Non-Fibered Emulsion Dampproofing at the rate of 2 to 3 gallons per 100 sq. ft. If applying two coats, each coat should be 2 to 3 gallons per 100 sq. ft. (First coat must be allowed to dry prior to the application of the second coat).

Fabric reinforced dampproofing: Apply one coat of 100 Non-Fibered Emulsion Dampproofing at a rate of 2 to 3 gallons per 100 sq. ft. Apply 31 Fiberglass Membrane or 34 Asphalt Saturated Cotton Fabric over the wet coating, overlapping all edges. Smooth out all wrinkles, making sure there is no trapped air underneath the fabric. Proceed with the second coat at a rate of 2 to 3 gallons per 100 sq. ft.

Polystyrene insulation adhesive: 100 Non-Fibered Emulsion Dampproofing is a water-based asphlat emulsion that is 100% compatible wiht polystyene insulation or protection board. As an adhesive 100 Non-Fibered Emulsion Dampproofing should be applied in 4" diameter dabs directly to the insulation and immediately pressed into place.

Note: When more than two courses are required, wall ties may be necessary. Allow the film to cure for a minimum of 24 to 48 hours prior to backfilling. Care should be taken during backfilling not to puncture or damage the coating. A protection board is highly recommended, and backfilling should take place within 7 days.

COVERAGE RATE:
Apply at 2 to 3 gallons per 100 sq. ft. (32-48 wet mils) depending upon porosity and irregularity of the surface.

Do not apply when rain is imminent. Protect from freezing. Coating must be dried before exposure to water. Store in a heated room and keep container covered when not in use. Do not thin. Avoid prolonged contact with skin. Dispose of in an environmentally safe manner. Exterior use only.

CARE OF TOOLS:
Tools and other equipment should be cleaned with water immediately after use. Dried coating may be cleaned with mineral spirits. Take necessary  precautions when handling combustible material.